operanthouseのヘッダー
Kitaya lab
Parts printing
Print parts of OperantHouse listed below under the following conditions. Small parts can be printed at once.
Layer height: 0.2mm
Infill density: 20%
Top Thickness: 0.8mm (if not otherwise stated)
Print speed:
Initial layer: 30 mm/s
Other layers: 100 or 150 mm/s (150 mm/s can make tiny gaps between traces on the top surface of the printed objects that can hold animal odors)
Use light gray PLA plus filament unless otherwise specified (PLA plus is a water-resistant version of PLA).
| Part name | Num | Model | Print condition | Note |
| Tray.stl | 1 |  |
||
| SquareRocker6mm.stl | 2 |  |
||
| Body.stl | 1 |  |
Printing with 30% infill density may be better. | |
| BodyBeam.stl | 2 |  |
||
| MonitorPushAdapter.stl | 6 |  |
||
| Leg_BodyFront.stl | 1 |  |
||
| Leg_BodyRear.stl | 1 |  |
||
| WaterArm_Naked.stl | 1 |  |
Use the first and third holes from the top to install servo. | |
| WaterArm_Naked_Cover.stl | 1 |  |
||
| WaterArmBottom.stl | 2 |  |
||
| WaterArmMat.stl | 2 |  |
||
| WaterArmHolder_55mm_JCL_CL2704.stl | 1 |  |
If CL2704 (CLEA Japan) is used | |
| WaterArmHolder_63mm_Ancare_PC8HT.stl | 1 |  |
If PC8HT (Ancare) is used | |
| Chamber_Panel_Lever.stl | 1 |  |
Top thickiness: 1.6 mm |
Make sure not to make gap between filament traces on the floor. |
| Leg_Chamber.stl | 4 |  |
||
| MaskHolderTall.stl | 4 |  |
||
| ChamberSpacer2mm.stl | 2 |  |
||
| LeverHoleCapL.stl | 1 |  |
If lever module is not used | |
| LeverHoleCapR.stl | 1 |  |
If lever module is not used | |
| Roof_220117.stl | 1 |  |
||
| RoofStop_211215.stl | 4 |  |
||
| CameraCover_TouchScreen_230124.stl | 1 |  |
||
| Mask_InwardSlope.stl | 1 |  |
||
| MaskHoleBottom.stl | 1 |  |
Print with black filament |
Print the following parts only if necessary.
Option parts for lever module
| Part name | Model | Print condition | Note | |
| Lever.stl | 1 |  |
||
| LeverCase1.stl | 1 |  |
||
| LeverCase2.stl | 1 |  |
||
| LeverCase3.stl | 1 |  |
||
| LeverCaseGuideBottom.stl | 1 |  |
||
| LeverCaseGuideLWall.stl | 1 |  |
||
| LeverCaseGuideRWall.stl | 1 |  |
||
| LeverCaseGuideSpacer.stl | a few |  |
||
| LeverHoleCover.stl | 1 |  |
||
| CameraCover_NoTouchScreen.stl |  |
Doesn't have a slit for the touch screen monitor | ||
| MaskForLever.stl |  |
A mask without hole | ||
| Chamber_LeverOnly.stl |  |
Top thickiness: 1.6 mm |
A chamber with a fixed no hole mask |
Option parts for infrared sensor bar
| Part name | Model | Print condition | Note | |
| MonitorSpacer3.5mm_Sensor bar.stl | 2 |  |
||
| MonitorSpacer1.5mm_Sensor bar.stl |  |
|||
| RoofForSensorBar.stl | 1 |  |
||
| BackPlateArm_SensorBar.stl | 1 |  |
||
| BackPlateTop_Sensor bar.stl | 1 |  |
Better to print with black filament | |
| BackPlateBottom_Sensor bar.stl | 1 |  |
Better to print with black filament | |
| Mask3holesAirBar.stl |  |
|||
| Mask10holesAirBar.stl |  |
Other option parts
| Part name | Model | Print condition | Note |
| CueLedCover.stl |  |
Cue LED cover | |
| Chamber_TouchScreenOnly.stl |  |
Top thickiness: 1.6 mm |
A chamber without holes for lever modules |
| WaterArmHolder_48mm_JCL_old.stl |  |
If old water bottle from CLEA Japan (48mm width) is used. |